Fun Times in Fantasy Worlds~*~ from Sci-fi to DIY

Category Archives: Movie Recreations

My Rapunzel customer had a special request for the winter of 2013.  She was attending Disney on Ice in costume and needed a special jacket or cape to wear.  We came up with a gorgeous design, found the perfect matching velveteen/velour, lined it with purple and a special lace trim.  It ties at the neck with a velvet ribbon and has a huge hood.  It ended up being super thick and warm and a great accessory for the Rapunzel Dress.

rapunzel cape


Here is the original costume, above …..  and my recreation , below.


photo (44)

I had been wanting to do Rachael for years!  ( Like 10 years!).   This was finally the year, and I got to wear it for 3 different Halloween events.  I am now a pro at the 1940’s style rolls.  This was a quick costume, so it is not as fully movie accurate as I will make one day.

I am not going to do a tutorial for this costume, because it was really just a quick remake/ alteration.  Here is the basic way I made this:

1.  Buy Black Suit

2.  Make the rest of the costume

Just Kidding:

1.  buy Black Suit.  Longer skirt.  Make sure when you flip up the collar, it comes close to closing at your neck.

2.  open collar out to make a high neckline (press)

3.  tailor jacket to be very fitted through the waist and lower arms

4.  add two sets of shoulder pads to the jacket

5.  redo buttons

6.  add black leather/pleather patches.  These are supposed to be some kind of reptile skin.  I did the collar, the shoulders, the neck, either side of the waist, and one on each arm.  The neck diamond needs to be removable. ( I used double sided sticky velcro !!!)  To be movie accurate, there should be 3 on each side of the waist, and three on each arm, and only one shoulder..the left.

7.  the OWL.  I bought a black halloween prop that had green light up eyes, and painted it with acrylics

photo (41)

7.  hair and makeup.  (THE KICKER)

For the hair, I would search you tube for pompadour roll, 1940’s victory rolls, hair rolls, etc.  I actually used a stuffed “roll” under the front roll since my hair is very thin.

THIS page has lots of snapshots of the hair and makeup on set.


THIS thread has some amazing details of the jacket construction and medallions someone did a few years ago.  Better than most others found online.  I will be using this when I remake this costume.

And finally, I LOVE this artist rendition of Rachael by Paul X Johnson.



This is my next project and I realize I have done an awful job of doing instructions in the past. I have prettied up the blog a little, and will start this one in a detailed and nice looking manner.  It will be a post that will be updated, so hopefully I can keep it up.

  First steps were to get customer measurements, gather lots of reference photos, and do a basic sketch.  I decided to do two pieces; a bodice with attached sleeves and an elastic waist skirt with white slip underneath.

Second step was to order the custom printed fabric from Spoonflower here

There is a lighter colored print for the bodice and a darker one for the center panel of the skirt.




Since I did not make it to the store to purchase matching materials yesterday, I made a stencil last night.  Using some close up photos of the embroidery on the skirt, I did about a 2 foot by 4″ sketch.   This embroidery goes up both sides of the front panel, as well as around the whole circumference of the skirt, so there is no way I am going to embroider all of that by hand!  I could use an applique lace or spend a year trying to program my embroidery machine to do this, but I decided on painting it with my stencil.  I like to use what I have handy often times, so I cut the thick clear plastic covering on a binder off to use as my template.  I traced over my paper template onto the clear plastic and cut it out with an exacto knife.  I did not need to cut the pieces out of the paper template, but did not realize this until I realized a paper template would not work with the paint.

photo (1) has a good image of the embroidery sketch uploaded


Made it to the store today and found matching the purple in the darker print for the skirt was super hard.  Luckily, I had an old formal dress that I had forgotten about and it was the perfect shade.  I also picked up my lilac for the sleeves, pink ribbon for the stripes and corset lacing, fabric paint and brushes.    I had the whole evening to work (minus dinner and bedtime for kiddo)

Photo (8)

First, I drafted a pattern using McCalls 4107.  This is a pattern designed to end at the high waist, so I had to extend it down about 3-4″. I just slightly flared the bottoms..more is better because I ended up trimming to what was shown after fitting it on my mannequin. You can also see a few other changes I made.  I cut the strap back edge and taped it to the front strap and added some more length ( add more next time!)  I also curved the front edge at the top so it will look more like hers (at the red block).  You will also see where I did not place the back piece on the fold, rather, I placed a cut there and even added more onto the back edge.

Photo (13)

 I had some fabric of the dark pink polka dot variety, so I did my first try with this.  It only needed minor adjustments on my mannequin, so decided to use it as my liner rather than make a new liner.  I left the back seam open for final adjustments unlike the pattern which had a one piece back panel.   I made bone casings with my pink ribbon on the RIGHT side of the liner.  Just because.  I normally do them on the wrong side, but this was just too cute.  I order my steel bones from and always have a good variety in stock, so found some to fit leaving at least 5/8″ at each end.  You don’t want your bones extending into your seam allowances because then you can’t turn it!  After sewing the seams, I had two pieces:  front side back right, and front side back left.

Photo (9)

I then cut the same pieces from my printed fabric using the adjusted pattern, sewed them together the same.  Now, I had four separate pieces.  With right sides together, one liner and one outer, 5/8″ SA, I sewed full neck seam down the front edge and around the bottom.  Trimmed, clipped, and turned right side out!  Repeat for left side.  Shown below is the front edge.  The piece is still totally open on the back edge, so I reached in with a long bone and placed it at the front edge to keep it from bunching.  Just a running stitch on the other side of the bone made a channel to keep it in place.

Photo (2)

Once both pieces were done, I pinned it on my mannequin with a few inches open in the front where the laces and panel will go.  Here is the photo of how the back overlapped and the straps met.  I adjusted and marked where the straps should be attached.

Photo (7)

Before I took it off the mannequin to sew the straps, I also pinned the back seam as shown below.

Photo (6)

Then I took it back off and sewed the back seam and straps as I had marked them.   Finally it is in one piece!  I then trimmed the neck/back seam with little white lace and the bottom edge with a dark pink/white layered lace.

Photo (5)

That is it for the bodice for today.  Tomorrow I add sleeves, grommets and center panel.

I also got a lot done on the skirt today.  The liner from my formal was PERFECT.  I did not have to alter it at all.  I cut it 36″ long, the hem measured 52″ and the waist was around 38-40″, plenty large enough to gather into an elastic waistband.  Hopefully you can see in the following photo that I drew lines on the skirt.  I marked centers at top and bottom, then marked 5″ out on each side of the top center, then 9″ out from the center of the bottom hem.  I cut the exact same shape out of the darker printed material. 10″ X 36′ X 18″ X 36″ plus a small seam allowance for turning under the edges.  Then I just laid it on top of the skirt and turned under the edges along the sides and bottom and topstitched right to the skirt!  You can see the left side sewed down and the right side laying next to the white line I had drawn.  I also decided to stitch down the bottom edge instead of letting it flow free.

Photo (3)

That is enough for today, but have another free afternoon tomorrow to work on the stencil, petticoat and more!


Each portion of the stencil has to dry before I can move the skirt around and do another, so I started with doing one portion.  It turned out pretty well for my first try at painting a stenciled pattern onto fabric.  Words of advice, tape down the slippery stencil and place cardboard underneath to catch the bleed through.  This is light pink, but shows up white in the photo.  I will go back after it is done and touch up with lavender.

Photo (15)

While that was drying, I made the petticoat and put a lace ruffle around the bottom.  I made this about an inch longer than the skirt, so that it will be sure to peek out.   I can’t finish the skirt until the paint is dry, so petticoat is on hold for now.

In between portions of the stencil, it is back to the bodice.  I had a huge puffy sleeve pattern that I knew would be to big, so I trimmed it down to about 19″ X 11″ and cut my pieces of lavender satin out.  I marked lines and attached my pink ribbon stripes.  Unfortunately, in the second photo, you can see I put them on the shiny side of the satin, where I wanted to use the back/duller side!  No problem, I just turned it over and put new ones over the old stitch lines. 🙂

Photo (11) Photo (12) Photo (10)

I am still waiting to find the best sheer pink fabric for the bottom of the arm, so the sleeves are on hold, but I pinned one on, and the new pattern seems to look about right.  The bottom part of the arm needs to be attached before sewing the seam, so until I find that, the sleeves are the last thing to do!

I made a simple topstitched rectangle to act as the modesty panel for the front of the bodice, having finished edges even with 1/2″ below/above edges.  This one was about 6″ wide and 12.5″ long.  Knowing my customer was close to/ my mannequin, this left lots to spare.  I sewed it to one side leaving the other side free to lay flat underneath as the top was cinched.

Before attaching the panel, I had to put on the grommets, as the panel needs to be attached  not on the front edge but on the other side of the grommets so it does not interfere with the lacing.  In other words, it is “behind” the lacing (towards the side seam).   I eyeball all eyelets/grommets, but it was appx  1.5″ – 2″ between them.

Photo (18)

The stencil paint in light pink on the skirt did not come out as great as I had hoped, and to go back and do another layer would have been hard and messy.  I had wanted to do certain points in lavender to tie in the sleeves, but I ended up doing just an artistic touch up in lavender to all the lightly painted areas and I like it more than just an occasional touch of lavender!

Photo (17)

I was hoping to do a natural light shot today to show the actual colors of the costume, but it is rain, AGAIN!!!

In leiu of a true color shot, I will give you a field test.  My first sample of the paint on the fabric after a rain storm.  The fabric is drenched and dark, but the paint is not running.  Good to know.  Anita’s it is for future fabric painting.  I did no ironing, nor steaming and it is holding up perfectly!

Photo (16)

The bottom sheer part of the sleeve was last, and it was basically a square sized piece of sheer pink material edged in lace and sewn to the bottom of the sleeve pouf, gathering in the pouf  as it went around.  Finished.  Beautiful!

Custom Rapunzel of Tangled Renaissance Costume by MiaLa photo (37)

photo 3 photo 4

And another happy customer, above.

Oh…plus, I also got to make Flynn’s leather satchel!  🙂

(The close up on the bottom is PRE bone toggle)

photo 2

Custom Flynn leather satchel from Tangled

Princess Leia Classic White Dress

This classic Star Wars costume is one of the best known, but this was actually the first time I have been asked to create one!

It is shown without the silver squares on the belt, but I made those out of rubber clay and hand stitched them to the leather belt.

The dress was TWO layers of a light poly blend jersey with lots of movement and drape.  I used the Padawan’s Guide, as usual when researching patterns, fabrics and upclose pictures.  The hardest part of this was getting the perfect drape on the “hood” which is not even really a hood!  It ended up being perfect!

Princess Leia star wars back custom made costume

Satin lined bomber style jacket with black accents and rocking scorpion applique.  This is a size Medium and is available for sale, just message me to inquire!
Scorpion jacket from Drive custom recreation


Here is the original:


This is a custom job for a happy repeat customer.  We have lots of time to work on it, so every detail is being studied and recreated….it looks simple, but is more time consuming and fickle than even the Leia gold bikini!!


My customer, Megan, is making the brooch herself along with the draped pearls, so all I have to do is make a loose dress that will fit a faux preggo lady, right?  then attach her brooch?  ….NOT SO EASY… this is the tutorial for the dress only…


10+ yards silk or silky satin with a good drape to be used on the bias

5+ packages of nude binding tape

several spools of matching or slightly different thread for embroidery

sewing machine thread to match fabric

binding tape to match dress fabric

dress form stuffed to be pregnant and at your measurements

Matching zipper


snaps and or hook eyes (not sure how it is all going to come together yet….)


This outfit is so detailed that each seam took me about 2 hours to finish. …

STEP 1:  Build out your mannequins belly with a pillow..stuffing, anything under a tight wrapping.  Panty hose work great.  A tiny tank top is what I used.  This is doable without a mannequin, but is hard to get the drape right on yourself with a belly.

 STEP 2:  Pattern using muslin or large scraps.   I use the padawans guide as a reference for almost all of my SW costumes. There you find that there is a center seam with 4 panels radiating out and then the side seams.   The back panels have a zipper which is hidden by the waterfall cape.  Here are most of my front panels on the mannequin.  I really wanted a full look, like the original, which I had not really seen redone.).  I used large triangles of muslin, then draped and pinned them till I was satisfied.

amidala steel nightgown how to

How to make padme amidala’s steel lavender nightgown

Step 3:  Cut your panels.  On the bias, this took me the full 10 yards of fabric I had ordered!  To get this great drape, you have to place each pattern piece not up and down, but at a 45 degree angle. Leave extra at the back piece …this is where you can alter easily.

Step 4.  Cut the waterfall cape.  I chose to do it double sided.  60″ crepe satin and 60″ long.  This should be altered for the height of the wearer.  It was the max of their wrist to wrist….

Step 5:  Begin to assemble the front pieces.  Make sure your patterns are correct because you have 7 full length seams to either join together  by pressing seams and hand faggotting a loose hand stitched seam or pressing seams and spending only a few less hours doing it by a machine that will do it for you …but you have to feed it perfectly correctly….sometimes I might rather spend that hour sewing by hand…..What I did was press the seams, then sew the nude binding to one side, then to the other, then went down with the blue embroidery over, giving the look of a nude undergarment with the overlaying embroidery.  I have heard that to do the separate nude lining and do a true faggoting hand stitch on the exterior results in alot of unwanted movement, so I avoided this.

faggoting stitch by pfatt

Step 6:  Once it was pieced together, I draped it again on the stuffed mannequin to make the back zip and strap placement.  The back zip was easy, but with the straps, the padawan’s guide REALLY helped.    Here is a pic of mine, based on the diagram on the site:

Step 7:  From here, it was fit, so all I needed to do was face the top, hem the bottom and attach the brooch and pearl strands.

Step 8:  Then the final piece was the cape.  I tried hook and loops, but ended up using snaps to attach it to the neck piece.  To make the waterfall drape with hanging beads, I pulled it together at around or below the hip, and attached matching silverish pearls, then again near the calf.  With the shape I started from and this combo, I think I got pretty close to the original…

Sorry it won’t let me turn my images right now.

Finally, here it is …I still have to tack up the pearls along the breast, but for this blog, it’s done!!!

I will try to get back to this and fix the pictures, but really mean this to be an aid for people wanting to make it themselves.   For anyone interested in purchasing one, please email me directly at ( at), it is available by custom order and will run 350-400$.

Happy sewing and hope I was a help!!!!!

Here is the update, with the customer wearing it!

Custom made Blue Pregnant Nightgown by

Custom made Blue Pregnant Nightgown by


The top is a half corset, fully boned and lined with a lace up back.  The sleeves hang off the shoulders for an authentic recreation look.

The pants are harem style but not too baggy with a lace up closure in the back as well.  They can be made sheer as in the photo, or lined .  Also included are hand sculpted accessories:  headband scarf, necklace, and earrings.

Available on Etsy 2011, $285

%d bloggers like this: